CloudEdge App DocsSmart Wire-free Video Doorbell
Quick start guide for the Smart Wire-free Video Doorbell and its indoor chime, covering hardware overview, charging, app download, doorbell setup, LED status, chime pairing, installation, optional angle mounts, and troubleshooting.
The Smart Wire-free Video Doorbell is a battery-powered video doorbell with an indoor wireless chime, set up and managed through the CloudEdge app.
Need help? Many problems are solved by changing a single setting. If your doorbell does not work as expected, browse the Doorbell FAQs.
Note: Manual contents are subject to change without notice in accordance with our policy of continuous product improvement.
1. Meet the doorbell
- Camera
- PIR Motion Sensor
- Microphone
- Doorbell Button
- LED Indicator
- Speaker
- Unlock Pin
- Li-ion Battery Built-in
- Reset Button
- Micro USB Port
- Charging Indicator
- Micro-SD Card Slot
- Unlock hole
2. Meet the chime
- LED Indicator
- Settings
- Volume Control
- Select Ringtone
- AAA Batteries
Please mind the battery polarities when installing.
3. Charge your doorbell
Prior to the doorbell installation, please charge up your doorbell for about 8-10 hours till the charging LED turns BLUE from RED.
| LED status | Indication |
|---|---|
| Solid red | Battery charging |
| Solid blue | Fully charged |
Compatible charger (not provided): USB compatible mobile phone charger (DC 5V 1A~2A).
4. App download
Search 'CloudEdge' in the App stores or scan the QR codes in the booklet to download the App from the App Store (iOS) or Google Play (Android).
5. Set up doorbell
Press your doorbell to activate, and you will see the LED indicator flashes red (once per second). If not, press and hold the reset button for 5 seconds to restore factory defaults.
Start setting up your doorbell following the in-app instructions.
Tips:
- Please operate the setup near your Wi-Fi router.
- Make sure your phone is connecting to a 2.4GHz Wi-Fi.
- Make sure the doorbell is turned on, and its indicator LED is flashing red. If not, press and hold RESET for 5 seconds.
- Ensure the Wi-Fi signal is good, and the Wi-Fi password is correct.
| LED status | Indication |
|---|---|
| Solid red | Device is abnormal. |
| Flash red (once/sec) | Ready for Wi-Fi configuration. |
| Flash red (twice/sec) | Connecting to Wi-Fi |
| Solid blue | Device is online |
| Flash blue (once/sec) | Live-viewing doorbell cam |
| Flash blue (twice/sec) | Firmware upgrading |
6. Pair with your indoor chime
Click the SETTING button on the chime, and the chime will be in pairing mode for 20 seconds, with its red LED flashing.
Press the doorbell button to send a pairing signal, and your chime will sound to react, together with its blue LED flashing. Chime pairing succeeds.
Chime settings
Settings — Click to enter/quit pairing mode; press & hold for 5 seconds to restore factory defaults.
Volume control button — Click to control volume: level 1: 110 dB; level 2: 100 dB; level 3: 90 dB; level 4: 80 dB.
Ringtone selection — Click to change ringtone (4 ringtones available).
7. Install your doorbell
Select a location
It is suggested to mount the doorbell at least 4 feet (120 cm) above the ground for optimal angle of view and best motion detection performance.
Mount your doorbell
A. Release the rear mount using the unlock pin.
B. Mark the screw holes with the doorbell mount.
C. Mount the rear mount to your wall with screws and tools.
D. Adhesive tapes are optional to mount the doorbell on flat surfaces.
E. Attach the doorbell to its rear mount, and push the doorbell to lock up.
F. All set! Press the doorbell button to run a test.
8. Accessory (Optional)
Doorbell Angle Mounts
You can purchase the following angled brackets so as to point your doorbell to a specific view angle.
- Install with Corner Mount — Horizontal Angle ∠25° ~ 50° (Adjustable). Sold separately.
- Install with Wedge Mount — Vertical Angle ∠8° (Stackable). Sold separately.
9. Troubleshooting
Q1: Is the video doorbell powered by battery?
A1: Yes, there is a Li-ion battery built-in. Thanks to the low power consumption technology, a full charge lasts for more than 2 to 3 months in our lab test environment (Lab test condition: 10 events per day, 15 seconds video recording per event).
Q2: Does it support legacy hardwire power source?
A2: No, it doesn't. If you need longer battery endurance, suggest that adding a solar battery charger for your doorbell, if only there is sunshine in your doorbell location. You can contact our after-sale service to know where to buy.
Q3: Does it work with existing mechanical chime?
A3: No. The doorbell comes with a battery powered wireless chime to notify people when your visitor presses the doorbell button. And our wireless chime is 100% wireless, you can place it almost everywhere you like. The transmission distance in open space is more than 100 meters (328 feet).
Q4: How many wireless chimes can be added to the doorbell?
A4: You can add several wireless chimes to work with your video doorbell. And one chime can be paired with up to 8 video doorbells.
Q5: Does it support customized Motion Detection Zones.
A5: Yes it does. You can customize the detection zone in the doorbell settings.
Q6: Does the doorbell support cloud storage?
A6: Your doorbell support local video storage by TF card. And you can also activate the cloud storage service in the App so as to back up video clips into the cloud server. There is a 7-day-free cloud recording trial service.
Still need help? Visit the Doorbell FAQs.
100% Wire-free Video Doorbell & Chime
Quick start guide for the 100% wire-free video doorbell (Model Bell J7) and wireless chime (Model Chime06), covering charging, chime power, app setup, LED states, chime pairing, installation, tamper alert, and specifications.
Video Doorbell User Manual
Set up, charge, pair and install the CloudEdge battery-powered Video Doorbell and its wireless chime, with LED status, volume settings and troubleshooting.